總計 : 0
TPU樹脂
工程級
ISOTHANE 8000系列 - 工程級
| 項目名稱 | 工程級 TPU樹脂 |
|---|---|
| 產品特性 | 適用於射出及押出成型。 |
| 應用場合 | 電子、汽車、電動工具、家用電器、油水分離機、醫療器材、光學產品。 |
| 項目名稱 | 工程級 TPU樹脂 |
|---|---|
| Description | ISOTHANE 8000 series products are engineering thermoplastic polyurethanes. They exhibit excellent tensile and flexural strength, toughness, abrasive resistance, good fatigue resistance, solvent resistance, and maintenance of good physical properties under UV exposure. The product can be injection molded and extruded. |
| Supply and Storage | ISOTHANE TPU resins are supplied in pellet form packed in 25kg moisture proof bags. All TPU resins have been dried before packing. ISOTHANE TPU resins should be stored in cool and dry environment in their original containers until be used. Storage temperature should not exceed 30°C. If only a portion of TPU resins was used from a bag, the remainder of TPU resins should be tightly closed. |
| Drying | TPU resins are hygroscopic and pre-drying of TPU resins is always a necessary step before processing. Depend on the climate, the granule exposed to the atmosphere will absorb moisture very quickly. The moisture might bring about partial degradation of polymers and the formation of bubbles or streaks in the molded and extruded parts. In order to ensure the efficient and successful processing into quality parts, the moisture content in TPU resins is recommended less than 0.02%. A desiccant-bed-type hopper dryer is recommended for drying ISOTHANE TPU. The dew point of the inlet air should be in the range of -30 to -40°C. About the recommended drying conditions, please view ISOTHANE individual data sheets. |
| Processing - Extrusion | Barrel and Motor
|
| Processing - Injection Molding | Barrel and Motor
|
| Coloring | Generally, ISOTHANE TPU resins are supplied in their natural color. They can be colored by blending with pigment or pigment master batch. Using master batch based on TPU is recommended. Other master batch based on polyethylene or polystyrene is suitable to a limited extent. All colorants employed in TPU resins must be pre-dried before processing. The normal addition of pigment or pigment master batch is 0.2%-0.5% or 1-3%. |
| Additives | Various additives can be used to enhanced the properties of ISOTHANE TPU resins, e.g. anti-blocking agents, antioxidant, UV stabilizers or release agents. Most additives supplied as master batches are available. But not all additives are compatible with ISOTHANE TPU resins. It is recommended to inquire of your suppliers or our technical service before compounding. |
| Recycling | For ISOTHANE TPU resins, up to 20% of regrind may be recycled with virgin material depending on finished parts requirements. The regrind material has to be kept free of contamination, diced and dried before re-using. The material which has been contaminated, discolored or degraded is not suitable for recycling. TPU resins may decrease desired properties, e.g. hardness and mechanical properties, due to improperly mixing with regrind. Regulatory or testing organizations (e.g., UL) may have specific requirements limiting the allowance amount of regrind. Certain quality requirements laid down in specifications may exclude the use of regrind material. |
| Healthy and Safety Information | Before working with these products, it is essential that all operators are aware of the healthy and safety precautions. ISOTHANE TPU resins can be processed or machined over a wide range of temperature. There can be some smoke formation during processing. The smoke that contains some decomposition substances of TPU or additives may cause irritation to human body. Generally, the temperature does not exceed 240°C that can reduce decomposition formation. An effective extraction system, especially in the melt outlet zone, is necessary. The detail information concerning healthy and safety can be available in safety data sheets (SDS) or contact our technical service. |
| Disposal | ISOTHANE TPU resins present no hazard to the environment or water. They can be dumped on municipal landfill or in a waste incineration plant. The official regulations on waste disposal should be observed. |
| 項目 | Units | ASTM | 8101 | 8201 | 8301 | 8306 | 8102 | 8303 | 8309 |
|---|---|---|---|---|---|---|---|---|---|
| 比重 | D-792 | 1.20 | 1.19 | 1.20 | 1.20 | 1.18 | 1.20 | 1.20 | |
| 硬度 | Shore D | D-2240 | 80D | 81D | 85D | 80D | 76D | 78D | 83D |
| 抗拉强度 | MPa psi |
D-638 | 75 11,000 |
83 12,000 |
90 13,000 |
68 10,000 |
60 8,700 |
67 9,700 |
78 11,400 |
| 抗拉模數 | MPa psi |
D-638 | 1,480 214,000 |
1,570 228,000 |
1,880 258,000 |
1,280 186,000 |
1,080 156,000 |
1,350 196,000 |
1,700 242,000 |
| 斷裂延伸率 | % | D-638 | 125 | 40 | 40 | 193 | 150 | 92 | 34 |
| 彎曲強度 | MPa psi |
D-790 | 95 13,800 |
108 15,600 |
110 16,000 |
88 12,800 |
74 10,800 |
91 13,100 |
100 14,500 |
| 彎曲模數 | MPa psi |
D-790 | 1,730 250,000 |
1,850 268,000 |
2,000 290,000 |
1,630 236,000 |
1,370 198,000 |
1,580 229,000 |
1,730 250,000 |
| 耐衝擊強度 | J/m ft-lb/in |
D-256 | 117 2.2 |
108 2 |
113 2.1 |
108 2 |
1,060 20 |
646 12 |
356 6.6 |
| 熱變形溫度 | °C °F |
D-648 | 93 199 |
105 221 |
132 270 |
65 149 |
90 194 |
110 230 |
127 261 |
| 軟化點 | °C °F |
D-1525 | 100 212 |
112 233 |
142 288 |
77 170 |
98 208 |
129 264 |
139 282 |
| 外觀 | - | - | Transparent | Transparent | Transparent | Transparent | Opaque | Opaque | Opaque |
上表所列數據資料僅供參考
