防火級

總計 : 0

ISOTHANE FR系列 - 防火級

項目名稱	TPU防火規格、無鹵
產品特性	適用於押膜、押管及射出用途。
應用場合	電器、電線、電纜、及建材。

項目名稱	TPU防火規格、無鹵
Description	ISOTHANE 8800 series products have good initial adhesive strength, fast crystallization, good solubility, good washing durability and freezing resistance etc.. Viscosity ranges from 150~2800cps (15% MEK Solution), and viscosity could be customized for different viscosity. They exhibit good adhesive with TPU, PVC, polyester fabric, leather and other materials.
Supply and Storage	ISOTHANE TPU resins are supplied in pellet form packed in 25kg moisture proof bags. All TPU resins have been dried before packing. ISOTHANE TPU resins should be stored in cool and dry environment in their original containers until be used. Storage temperature should not exceed 30°C. If only a portion of TPU resins was used from a bag, the remainder of TPU resins should be tightly closed.
Drying	TPU resins are hygroscopic and pre-drying of TPU resins is always a necessary step before processing. Depend on the climate, the granule exposed to the atmosphere will absorb moisture very quickly. The moisture might bring about partial degradation of polymers and the formation of bubbles or streaks in the molded and extruded parts. In order to ensure the efficient and successful processing into quality parts, the moisture content in TPU resins is recommended less than 0.02%. A desiccant-bed-type hopper dryer is recommended for drying ISOTHANE TPU. The dew point of the inlet air should be in the range of -30 to -40°C. About the recommended drying conditions, please view ISOTHANE individual data sheets.
Processing - Extrusion	Barrel and Motor High torque drive capacity at low speed Vented or standard barrels acceptable Screw Compression ratios between 2:1 and 3:1 Minimum L/D of 30/1 Feed Throat Vertical and tangential Water cooling is recommended Screen Pack Streamlined breaker plates with screen packing is recommended Typical 40/80/80/40 mesh screens Die Streamline with good temperature control Land Length is generally 10 to 15 times the part thickness Coat-hanger manifold-type dies are recommended for extruding film and sheet Crosshead dies are recommended for wire, cable and hose jacketing Side-fed rotating dies are recommended for blown film About the recommended extrusion temperatures, please view ISOTHANE individual data sheets.
Processing - Injection Molding	Barrel and Motor High torque drive capacity at low speed Vented or standard barrels acceptable Screw Compression ratios between 2:1 and 3:1 Metering screw with gradual transition zone Injection Pressure Typical 6,000 to 15,000 psi Hold pressure 60 – 70% of forward time Injection speed Slow to moderate Depends on gating, wall section and flow length About the recommended injection molding temperatures, please view ISOTHANE individual data sheets.
Coloring	Generally, ISOTHANE TPU resins are supplied in their natural color. They can be colored by blending with pigment or pigment master batch. Using master batch based on TPU is recommended. Other master batch based on polyethylene or polystyrene is suitable to a limited extent. All colorants employed in TPU resins must be pre-dried before processing. The normal addition of pigment or pigment master batch is 0.2%-0.5% or 1-3%.
Additives	Various additives can be used to enhanced the properties of ISOTHANE TPU resins, e.g. anti-blocking agents, antioxidant, UV stabilizers or release agents. Most additives supplied as master batches are available. But not all additives are compatible with ISOTHANE TPU resins. It is recommended to inquire of your suppliers or our technical service before compounding.
Recycling	For ISOTHANE TPU resins, up to 20% of regrind may be recycled with virgin material depending on finished parts requirements. The regrind material has to be kept free of contamination, diced and dried before re-using. The material which has been contaminated, discolored or degraded is not suitable for recycling. TPU resins may decrease desired properties, e.g. hardness and mechanical properties, due to improperly mixing with regrind. Regulatory or testing organizations (e.g., UL) may have specific requirements limiting the allowance amount of regrind. Certain quality requirements laid down in specifications may exclude the use of regrind material.
Healthy and Safety Information	Before working with these products, it is essential that all operators are aware of the healthy and safety precautions. ISOTHANE TPU resins can be processed or machined over a wide range of temperature. There can be some smoke formation during processing. The smoke that contains some decomposition substances of TPU or additives may cause irritation to human body. Generally, the temperature does not exceed 240°C that can reduce decomposition formation. An effective extraction system, especially in the melt outlet zone, is necessary. The detail information concerning healthy and safety can be available in safety data sheets (SDS) or contact our technical service.
Disposal	ISOTHANE TPU resins present no hazard to the environment or water. They can be dumped on municipal landfill or in a waste incineration plant. The official regulations on waste disposal should be observed.

項目	Units	ASTM	Polyester FR-TPU
項目	Units	ASTM	1085A-FR	1085A-FRT	1090A-FR
比重		D-792	1.18	1.20	1.20
硬度	Shore A	D-2240	84A	85A	90A
抗張强度	MPa psi	D-412	32 4,620	36 5,260	35 5,120
@ 50% 延伸率	MPa psi	D-412	4 570	4 570	8 1,140
@ 100% 延伸率	MPa psi		5 780	5 710	9 1,280
@ 300% 延伸率	MPa psi		11 1,560	10 1,420	14 2,000
斷裂延伸率	%	D-412	610	600	600
撕裂强度	N/mm lb/in	D-624 DIE C	110 620	110 620	150 840
防火	-	UL-94	V-0	V-0	V-0
外觀	-	-	White	Transparent	White

項目	Units	ASTM	Polyether FR-TPU
項目	Units	ASTM	3080A-FR	3085A-FR	3085A-FRT	3085A-FRC	3090A-FR	3095A-FR
比重		D-792	1.15	1.15	1.18	1.20	1.15	1.18
硬度	Shore A	D-2240	80A	85A	84A	85A	91A	94A
抗張强度	MPa psi	D-412	20 2,920	29 4,270	33 4,840	15 2,130	30 4,400	25 3,560
@ 50% 延伸率	MPa psi	D-412	4 640	6 850	4 640	6 920	10 1,420	10 1,500
@ 100% 延伸率	MPa psi		6 850	8 1,140	6 850	7 1,070	12 1,710	12 1,710
@ 300% 延伸率	MPa psi		10 1,420	13 1,850	11 1,560	9 1,280	19 2,770	19 2,700
斷裂延伸率	%	D-412	610	570	700	710	480	400
撕裂强度	N/mm lb/in	D-624 DIE C	93 530	130 730	120 670	110 620	133 750	130 730
防火	-	UL-94	V-0	V-0	V-0	V-0	V-0	V-0
外觀	-	-	White	White	Transparent	White	White	White

上表所列數據資料僅供參考

proimages/thumb/image-cHJvZHVjdA==--product1473751561592131.png